Mellotron on the Raspberry Pi
Mellotron is one of those curious instruments that are impossibly difficult and expensive to own, but so deceptively simple and expressive that when you get to play one, you can’t let go of it. So of course I want one.
Note: you will need an audio interface that works with Jack. This will define how playable your new instrument will be! You will also need a MIDI interface, such as the USBmidi2, but any Linux-compatible audio interface will do.
Step 0: Acquire the necessary parts
The purpose of this post is to demo the USBmidi2. So I have one of those for connecting a MIDI keyboard. It will let you plug in a laptop also.
For the audio I used an old Terratec audio interface that I was familiar with. You can use any audio interface that you can get Jack to work with. The Raspberry Pi’s internal headphone jack will also “work”, kind of, but it requires so long buffer sizes that it’s unusable.
The Mellotron sample bank is available on the LinuxSampler instrument page.
Step 1: Configure Jack
Sorry, this part I will not explain here in detail. I used jackd2 and qjackctl. I was able get a latency of 2.9 ms at 44.1khz (according to qjackctl)!
You have to make sure that your Pi is configured to output audio at the minimum possible latency with minimum glitches, before you continue.
For testing Jack, I simply played some mp3s with
mplayer -ao jack [song.mp3]
Step 2: Acquire LinuxSampler sources
I had to install a few dependencies first (I already had a g++ installed):
sudo apt-get install subversion bison flex libtool automake autoconf intltool libsqlite3-dev patch
Then download the sources:
svn co https://svn.linuxsampler.org/svn/libsf2/trunk libsf2
svn co https://svn.linuxsampler.org/svn/libgig/trunk libgig
svn co https://svn.linuxsampler.org/svn/liblscp/trunk liblscp
svn co https://svn.linuxsampler.org/svn/linuxsampler/trunk linuxsampler
Step 3: Build the support libraries
Build libsf2, libgig, and liblscp in that order.
To build each, run these commands:
sudo make install
Some of them may require some variation or some commands were unnecessary; I will make better notes if I have to do this from scratch. Make sure the
make install steps finish completely before continuing to the next.
Step 4: Patch LinuxSampler sources for the Raspberry Pi
LinuxSampler does not support the ARM CPU of the Raspberry Pi out of the box. Luckily someone has already fixed this, and the necessary patches are available here. You need both the RTMath.cpp patch, and also the attached atomic.h.diff patch. Or you can just grab them from my site.
Apply the patches:
patch < ~/RTMath.cpp.diff patch -p2 < ~/atomic.h.diff cd ../..
Step 5: Build LinuxSampler
There are a few programs in
linuxsampler/scripts/ that you have to run first, before LinuxSampler is ready to compile. I ran them all on order:
Those perl scripts required XML::Parser to run, but I think that installing ‘intltool’ adds the necessary dependencies. If not, make sure to see “Installing packages system-wide” before going on installing all the Perl libraries with
Step 6: Build LinuxSampler
This will take some time if you do it on the Pi, and it will require several hundred megabytes of disk space.
The same commands work as before, but configure required some help:
CFLAGS="-I/usr/include/sf2 -I/usr/include/libgig" CPPFLAGS="-I/usr/include/sf2 -I/usr/include/libgig" ./configure --prefix=/usr
sudo make install
You should now be able to run ‘linuxsampler’ in a shell on the Pi.
Step 7, optional: Install qsampler on a PC
LinuxSampler allows the GUI to run remotely. You can build qsampler to run on a more powerful computer, and connect to the Pi with it. The sources are in the same subversion repository.
Step 8: Install the sample bank and configure LinuxSampler
Extract the TaijiguyGigaTron.tar.bz2 from the LinuxSampler instrument page on the Pi. If you use qsampler remotely, the .gig file must be at the exact same path on both the Pi and your remote controller host.
I ran out of disk space at this point. Running “make clean” in the linuxsampler source tree will make you some room. I was able to fit everything on a 4 GB disk by removing a bunch of unnecessary locales from /usr/share/locale. My Raspbian also came with a rather large General Midi sound bank in /usr/share/, see if you can find it! (OK, I’m assuming it was General Midi, I deleted it before listening to it.)
Now you have to create a LSCP (LinuxSampler Control Protocol) script that initializes your hardware and loads the Mellotron sample bank. I did it like this:
- Start linuxsampler on Pi
- Start qsampler on PC
- In qsampler:
- Disable local server
- Connect to “raspberrypi”
- Add ports for your audio and MIDI hardware
- Add a channel with TaijiguyGigaTron_switched.gig
- Make sure the green “led” in qsampler blinks when you play notes – if not, check your MIDI connections!
- Make sure sound comes out when the green “led” blinks – if not, check your audio connectiosn!
- Save settings to LSCP file, I called mine “TaijiguyGigaTron.lscp”
Then copy the LSCP file to your Pi. My example LSCP file is available for download here, but I’m sure that you will have to modify it to work with your choice of hardware.
Step 9: Set up LinuxSampler to start without remote control
There’s a nice trick to load the LSCP file from the previous step on the Pi.
First run LinuxSampler in one shell on the Pi:
When it says “initialization completed”, send the LSCP file to it in a second shell:
cat TaijiguyGigaTron.lscp | netcat localhost 8888
If you didn’t change anything else since Step 7, you should now be able to play notes with the Mellotron patch.
Step 10: Wrapping it up in a script
To prepare for starting everything in one go, I wrote a simple script that kicks off Jack and LinuxSampler. OK, it’s dirty with those sleeps and all, but works pretty well for a quick hack.
I have this in /home/pi/jackd.sh, you have to replace the jackd command line with whatever your hardware needs:
daemon -e "DISPLAY=:0.0" -- /usr/bin/jackd -P10 -dalsa -dhw:USB2448 -r44100 -p64 -n2 -Xseq -P
daemon -- linuxsampler
cat /home/pi/TaijiguyGigaTron.lscp | netcat localhost 8888
Debugging it is easy; you can add the
-f parameter to
daemon to run the programs in a terminal. That allows you to directly see the jack error messages. And when you get each step to run properly, just update the parameters in the script and continue with the next.
Step 11: Running Jack and LinuxSampler on startup
I found it easiest to add my script to the LXDE autostart scripts. I had two directories in /etc/xdg/lxsession/, and I’m not sure why, so I added it in both:
sudo nano /etc/xdg/lxsession/LXDE/autostart
# add on new line at end of file: /home/pi/jackd.sh
sudo nano /etc/xdg/lxsession/LXDE-pi/autostart
# add on new line at end of file: /home/pi/jackd.sh
Save everything, test it a few times, reboot, and you’re ready to rok!